Residential Blower Door testing only Available in Melbourne and the whole of Victoria.
Multi-dwelling residential available Australia wide.
Efficiency Matrix use calibrated, quarterly tested, state-of-the-art pressure testing equipment, to verify the air tightness of a building for energy efficiency.
Top reasons why you should seal your home and check it with residential blower door testing:
- Return on investment. Air leakage can be responsible for 40% of the heating load. Draught sealing your home can save you significantly.
- Finding and reporting on issues you would not have necessarily have known about.
- Whole house comfort. It will make your home more comfortable overall. Having one room too hot and another too cold is less likely when you have an air tight home.
- Painless and immediate. It’s quick, quiet and most of the time not very intrusive. Up to 80% of air sealing a home can be done in a day, and you’ll notice the difference immediately.
- Noise Reduction. Air sealing also reduces noise from outside coming inside.
- Improve indoor Air quality. If you have allergies, air tightness can reduce pollen entering the building envelope
- Pest Control. White tale spiders through to rodents are common pests that enter the building envelope via draughty homes.
Our thermal imaging technology helps people find trouble spots of draughts as well as potential issues with moisture and insulation inconsistencies.
Blower Door Testing can help identify and resolve the following:
1. Uncontrolled ventilation
In Australia, new and old homes can be extremely leaky compared to homes built overseas. As a result, our buildings are “automatically ventilated”. Over-ventilation can contribute to moisture problems, as it can be carried inside from outside air, people also producing more water vapour, by taking showers, washing and cooking which contributes to moisture problems again. That means that you still must ventilate, but we must ventilate more effectively. Permanently open or louvred windows should be avoided, otherwise, your heating costs are going to go up dramatically. A controlled ventilation system (via Energy Recovery Ventilation systems) is the optimum solution. It always provides for the perfect air change.
2. Leakages in the building envelope
Small leakages in the building envelope and a lack of insulation are sufficient to let warm and damp indoor air escape. On its way out, the air cools down and the water vapour carried along with it condenses. This condensation can accumulate in the insulation layer and can lead to mould infestation after a few months. Mould can cause damage to certain building materials and therefore can lead to serious building damage. This is why an air and windtight building envelope is absolutely necessary, for building health and energy efficiency.
A useful table to understand Air tightness benefits of a home.
|ACH50||Natural Air Changes||Rating||% of Bill||% savings potential||Ventilation Requirement|
|1.5||.075||Super||2%||None||Constant energy recovery ventilation|
|3.5||.18||Excellent||6%||1 to 3%||Occasional forced ventilation|
|5||.25||Better||10%||2 to 4%||Occasional|
|7||.35||Good||14%||2 to 5%||Small|
|10||.5||Fair||20%||3 to 10%||Rare|
|20||1||Bad||40%||5 to 20%||Little to none|
|Location||Building Type||Est Build Age||Volume||Area||ACH50||Natural ACH|
|Mt Eliza||Brick veneer with wood panel ceiling||1970's||540||180||12.96||.65|
|Blackburn||Brick veneer, internal ceiling boards, exposed beams||1960's||504||180||16.94||.85|
|Brunswick||Weatherboard clad, renovated ext and internal||2000's||150||40||15.2||.75|
|Ascotvale||Weatherboard with Evap Cooling||1960's||280||100||21.98||1.99|
|Mount Waverly||Brick Vaneer||2000's||518.2||203||16.886||.84|
|Mount Waverley||Brick Vaneer||2000's||442||170||8.87||.44|
|Wheelers Hill||Brick Vaneer with Evap Cooling||1970's||381||158||24.01||1.2|
|Wheelers Hill||Brick Vaneer||1970's||381||158||19.711||.99|
|Wheelers Hill||Brick Vaneer||1970's||381||158||10.01||.5|
|Retrofit||Size||Air Change Per hour at 50Pa||Air Change Per hour at Ambient|
|Evap Cooling installed||158m2||24.01||1.2|
|No Evap Cooling||158m2||19.711||.99|
|Draught proof home, Caulking and window and door seals||158m2||10.01||.5|
|Standard||House Leakage based on floor area of: 210 square metres||ACH50|
|ATTMA TS-1||UK, Best Practice, residential||3.4|
|Oregon||3.5 to 5 is Tight, great||3.5|
|ASTM E779||LEED, 1.25 sq in at 4 Pa / 100 sq ft. Envelope||4.7|
|PA Housing||Tight < 5 Housing Research/Resource Center (PHRC)||5.0|
|EEBA||Energy and Environmental Building Association Guidelines||5.2|
|EN13829||Most European countries||6.1|
|Oregon||5 to 7 is good||7.0|
|PA Housing||Moderate < 10, Leaky > 10 Housing Research Center||10.0|
A retrofit case study to show how air leakage in a home changes after resolving trouble spots (this included pulling out a 2-year-old evaporative cooling system).
Should you have any concerns in your home that air Leakage maybe pushing up your heating and cooling costs, don’t hesitate to get in contact with us regarding residential blower door testing.
Always insist that air tightness testing is conducted using the ATTMA standard.
For a bare-bones example air tightness test report, click below, for the Master Builders Course.